One common question that is asked by roller skaters is what material can be used to clean the bearings on their skates.

There are a few different materials that can be used, but some work better than others.

One of the most popular methods is to use a cleaning agent that is made specifically for roller skate bearings, such as Speed Clean or Bearings Express.

However, some people choose to use household items, such as rubbing alcohol or glass cleaner.

Below we will look at what other things you can use to clean your roller skate bearings.

what you can use to clean your roller skate bearings?

There are a variety of materials you can use to clean roller skate bearings, some of which are listed below.

1. Using a toothbrush and hot water

When it comes time to clean your roller skate bearings, you may be tempted to reach for the nearest can of compressed air.

However, there are other ways to get the job done – and they don’t involve spending money on specialty products. In fact, you can use a toothbrush and hot water to clean your bearings quite easily.

Just be sure to take care when doing so. Bearings can be damaged if they’re overheated, so use caution when applying heat. You don’t want to risk burning yourself or damaging the bearing in any way.

Once they’re clean, allow them to cool before putting them back into your skates.

2. Soaking in vinegar

Soaking your roller skate bearings in vinegar is a great way to clean them and make sure they are in good condition.

Vinegar is a natural disinfectant and cleaner, so it will remove any dirt or bacteria that may be on the bearings.

However, you need to be careful when using vinegar to clean your bearings. Make sure to soak them for a short period of time only, and don’t rinse them off with water afterwards.

One thing to take note is that, if you rinsing them with water, it will cause the vinegar to react with the metal in the bearings and could damage them.

So, becareful when using vinegar.

3. Using alcohol

A lot of people may not know this, but you can clean your roller skate bearings by using alcohol. Make sure to be very careful when doing this, because if you get the alcohol on your skin it will sting.

I usually use a small amount of isopropyl alcohol on a cotton ball and then wipe the bearings down. I do this every few weeks or so, and it helps keep them running smoothly. Be sure to let them dry completely before putting them back in your skates!

4. Soap and water

If you’ve been skating for a while, you’ve probably noticed that your roller skate bearings start to get a little dirty. This can cause the bearings to not work as well, and they may even start to make noise. Luckily, there is an easy way to clean them – using soap and water.

Make sure that you are careful when cleaning your bearings, as it is easy to damage them.

First, remove the shields from the bearings (if they have any).

Then, fill a bowl with warm water and add some soap. Place the bearings in the bowl and let them soak for a few minutes.

After they have soaked, use a toothbrush or something similar to scrub them clean.

Rinse them off with warm water and then dry them off with a towel.

Replace the shields (if they have any) and you’re done!

5. Glass cleaner

If you’re a fan of roller skating, then you know that keeping your bearings clean is important if you want to keep skating smoothly. Luckily, cleaning them is a breeze – all you need is some glass cleaner!

Make sure to shake the glass cleaner well before spraying it on the bearing.

Hold the bearing with one hand and spray the glass cleaner on the other side.

Give it a good scrubbing with a toothbrush – make sure to get into all of the nooks and crannies.

Rinse off the glass cleaner and let the bearing dry completely before putting it back in your skates.

Be careful not to get any glass cleaner on the rubber seal, as it can damage it.

Also, be careful not to get any glass cleaner in your eyes – it can really sting!

6. Petroleum jelly

If you are a fan of roller skating, you know that the key to a good skating experience is having well-functioning roller skate bearings.

Unfortunately, over time, these bearings can become dirty and damaged, which will impact their performance. Luckily, there is an easy way to clean them – using petroleum jelly!

Before beginning, make sure that your roller skate bearings are completely dry. If they are not, the petroleum jelly will only further damage them.

Then, take a small amount of petroleum jelly on your finger and rub it into each bearing. Make sure to be careful not to get any of the jelly on the metal axle or on the rubber surrounding the bearing – both of these areas should remain dry.

Let the jelly sit on the bearings for about 5 minutes before wiping it off with a paper towel.

Your roller skate bearings should now be clean and functioning properly!


In conclusion, there are several methods that can be used to clean roller skate bearings. Each method has its own benefits and disadvantages.

So, It is important to choose the method that is best for you and your needs.


My name is Patricia Toh. I was born in the southen of China but I live in Hawaii. I work as a translator. I love skating. But in the future, I’d like to try yoga too."

Write A Comment